49 results found for 'clamp screw'. |1|2 | Next | View 100 per page
Matching rule: Every word must match (produces better results) | Only one word must match (Produces more results)
Try removing a word: clamp screw
Low relevance matches: 187 other results may be of interest to you. Show low relevance matches
49 results found for 'clamp screw'. |1|2 | Next | View 100 per page
Matching rule: Every word must match (produces better results) | Only one word must match (Produces more results)
Try removing a word: clamp screw
Low relevance matches: 187 other results may be of interest to you. Show low relevance matches
IEC Horizontal Pulley 50mm Diameter with Clamp Screw
IEC HORIZONTAL BENCH MOUNTING PULLEY
A 50mm diameter high quality nylon pulley mounted on a strong aluminium frame for clamping to a bench top or similar flat surface to a maximum 25mm thickness. The side of the pulley clamps parallel to the surface of the bench. The clam...
Order code: MF2590-001
IEC Ripple Tank Clamp Screw for Leg with Wing Nut
IEC RIPPLE TANK CLAMP SCREW FOR LEG WITH WING NUT
A clamp screw with wing nut and cupped washer for the leg of the SW3430-001 IEC Ripple Tank.
The stainless steel legs are held to the moulded plastic frame by these aluminium clamp screws. The leg passes through the clam...
Order code: PA3430-010
IEC Ripple Tank Support Bar Clamp Collar & Screw
IEC RIPPLE TANK SUPPORT BAR CLAMP COLLAR AND SCREW
A replacement clamp collar and screw for the PA3430-006 stainless steel bar that supports the variable speed rippler of the SW3430-001 IEC Ripple Tank
Order code: PA3430-016
Boss Head - Die Cast Aluminium Alloy with Plastic Head Clamping Screws
Bosshead, die-cast aluminium, takes up to 19mm diameter rod.
Order code: SC7340
Boss Head - Die Cast Aluminium Alloy with Metal Head Clamping Screws
Die-cast aluminium bosshead, takes up to 24mm diameter rod.
Overall length with clamps fully extended: 180mm
Width: 40mm
Order code: SC7345
IEC Clamp Bench Alloy Universal for 13mm Maximum Rods
IEC UNIVERSAL BENCH CLAMP FOR UP TO 13mm RODS
The IEC designed alloy Universal Bench Clamp can fit to benches up to 40mm thick and, when clamped, can carry rods up to 13mm diameter both vertically and horizontally.
The clamp is complete with large steel knurled head kno...
Order code: LB0858-001
IEC Collision In 2 Dimensions Kit
IEC COLLISION IN 2 DIMENSIONS KIT
This simple device clamps to a bench and allows balls of different mass to collide at angles to calculate the laws of dynamics and mass. The point that the balls reach the floor is shown by carbon paper leaving a mark. A plumb bob from be...
Order code: MF1000-001
Vernier Go Direct Sensor Clamp
VERNIER GO DIRECT SENSOR CLAMP
Vernier's Go Direct Sensor Clamp securely fastens to a wand-style Vernier Go Direct sensor and the included lanyard works as a strap to prevent accidental drops during investigations in the field.
Relax knowing students won’t drop their s...
Order code: GDX-CLAMP
Vernier Plastic Tubing Clamp (Pack of 100)
VERNIER PLASTIC TUBING CLAMPS
These easy-to-use clamps are great for providing an airtight fit for transpiration experiments.
Order code: PTC
Vernier Motion Detector Clamp
VERNIER MOTION DETECTOR CLAMP
The Motion Detector Clamp screws into the back of the Motion Detector and then it can be clamped to a variety of objects such as table tops, ring stands etc.
Order code: MD-CLAMP
Vernier Rod Clamp
VERNIER ROD CLAMP
The Vernier Rod Clamp is used to attach one end of a Vernier Dynamics Track to a vertical ring stand rod. This configuration is most often used to create a ramp.
Order code: RC-VDS
Retort Clamp Alloy with Cork Lined Jaws
This is the best made Retort Clamp that we have seen. Made of die-cast alloy with tight tolerances on all pivot points to ensure that jaws close without fouling each other. The design incorporates a mechanical stop that prevents the jaws from being overtightened and possibly br...
Order code: LW1667-01
IEC Pulley Vertical Adjustable with Universal Bench Clamp
IEC VERTICAL PULLEY WITH BENCH CLAMP
A very strong, low friction 50mm diameter pulley mounted on a strong 200mm rod that is held by a very useful universal bench clamp. The pulley and rod are clamped into position so that the pulley runs in the vertical plane. The bench c...
Order code: MF2593-001
IEC Clamp Safety for Gas Syringe 100ml
IEC SAFETY CLAMP FOR GAS SYRINGES
A simple safety device for holding a gas syringe, supporting the body and the
plunger to prevent the plunger from extending beyond a certain point. Gas syringes are fragile and expensive and this clamp reduces breakages, reduces experime...
Order code: CH0860-001
Clamp Burette Polypropylene Double
A double polypropylene burette clamp with spring loaded clamps to hold the burettes. Supplied with two inserts to allow use with retort stand diameters of about 9.5mm to 13.5mm.
Order code: LW1637-01
Pulley - Aluminium - 70mm Diameter - Vertically Mounted on a G Clamp
A 70mm diameter aluminium pulley mounted vertically on a G-Clamp. Can be clamped to a bench or table up to approximately 35mm thick.
Order code: MS0358-01
IEC Dissectible Transformer Iron Core Clamp
IEC DISSECTIBLE TRANSFORMER IRON CORE CLAMP
A replacement clamp moulded from GFN with moulded-in steel pin to fit the 35x35mm 'U' iron cores as included in the EM1660-001 IEC Dissectible Transformer Kit.
Does not fit the old 40x40mm 'U' cores.
Order code: PA1660-008
Nalgene Erlenmeyer Flask Screw Cap PC 500ml
This Nalgene branded transparent flask is made of polycarbonate with embossed graduations marked in millilitres and a polypropylene closure.
Features:
Far safer than glass flasks for use in shakers.
Closures are linerless, noncontaminating.
Flasks and closures are a...
Order code: 4108-0500
Bottle Reagent Clear Glass Graduated with Blue Screw Cap 1000ml
1000mL graduated glass multi-purpose reagent bottle with blue screw cap and plastic ring seal.
Order code: LW1071-01
49 results found for 'clamp screw'. |1|2 | Next | View 100 per page